?2004 littelfuse lp e1 - 1 http://www.teccor.com thyristor product catalog +1 972-580-7777 * selected packag es u.l. recogn ized file #e71639 mt2 mt1 g sensitive triacs (0.8 a to 8 a) e1 general description teccor's line of sensitive gate triacs includes devices with current capabilities through 8 a. voltage ranges are available from 200 v to 600 v. this line features devices with guaranteed gate control in quadrants ii and iv as well as control in the commonly used quadrants i and iii. four-quadrant control devices require sensitive gate triacs. they can be controlled by digital circuitry where positive-only or negative-only pulses must control ac current in both directions through the device. note that triacs with low i gt values in quadrants ii and iv will have lower dv/dt characteristics. the sensitive gate triac is a bidirectional ac switch and is gate controlled for either polarity of main terminal voltage. it is used primarily for ac switching and phase control applications such as motor speed controls, temperature modulation controls, and lighting controls. the epoxy to-92 and to-220 configurations feature teccor's electrically-isolated construction where the case or mounting tab is internally isolated from the semiconductor chip and lead attachments. non-isolated epoxy to-202 packages are available as well as to-251 and surface mount to-252 (d-pak). tape- and-reel capability and tube packing also are available. see ?packing options? section of this catalog. all teccor triacs have glass-passivated junctions. this glassing process prevents migration of contaminants and ensures long- term device reliability with parameter stability. variations of devices covered in this data sheet are available for custom design applications. consult factory for more information. features ? electrically-isolated packages ? glass-passivated junctions ensure long device reliability and parameter stability ? voltage capability ? up to 600 v ? surge capability ? up to 80 a ? four-quadrant gating guaranteed compak sensitive gate triac ? surface mount package ? 0.8 a and 1 a series ? new small profile three-leaded compak package ? packaged in embossed carrier tape with 2,500 devices per reel ? can replace sot-223 to-202 to-92 3-lead compak * to-220 isolated e1 to-252 d-pak to-251 v-pak www..net
sensitive triacs data sheets http://www.teccor.com e1 - 2 ?2004 littelfuse lp +1 972-580-7777 thyristor product catalog see ?general notes? on page e1 - 4 and ?electrical specification notes? on page e1 - 5. i t(rms) part no. v drm i gt i drm isolated non-isolated (11) to-92 compak to-220 to-252 d-pak to-202 to-251 v-pak (1) volts (3) (6) (9) mamps (1) (14) mamps qi qii qiii qiv t c = 25 c t c = 110 c max see ?package dimensions? section for variations. (12) min max max 0.8 a l2x8e3 l2x3 200 3 3 3 3 0.01 0.1 l4x8e3 l4x3 400 3 3 3 3 0.01 0.1 l6x8e3 l6x3 600 3 3 3 3 0.01 0.1 l2x8e5 l2x5 200 5 5 5 5 0.01 0.1 l4x8e5 l4x5 400 5 5 5 5 0.01 0.1 l6x8e5 l6x5 600 5 5 5 5 0.01 0.1 l2x8e6 200 5 5 5 10 0.01 0.1 l4x8e6 400 5 5 5 10 0.01 0.1 l6x8e6 600 5 5 5 10 0.01 0.1 l2x8e8 200 10 10 10 20 0.01 0.1 l4x8e8 400 10 10 10 20 0.01 0.1 l6x8e8 600 10 10 10 20 0.01 0.1 1a l201e3 l2n3 200 33330.010.1 l401e3 l4n3 400 33330.010.1 l601e3 l6n3 600 33330.010.1 l201e5 l2n5 200 55550.010.1 l401e5 l4n5 400 55550.010.1 l601e5 l6n5 600 55550.010.1 l201e6 200 5 5 5 10 0.01 0.1 l401e6 400 5 5 5 10 0.01 0.1 l601e6 600 5 5 5 10 0.01 0.1 l201e8 200 10101020 0.01 0.1 l401e8 400 10101020 0.01 0.1 l601e8 600 10101020 0.01 0.1 4a l2004l3 l2004d3 l2004f31 l2004v3 200 3 3 3 3 0.01 0.2 l4004l3 l4004d3 l4004f31 l4004v3 400 3 3 3 3 0.01 0.2 l6004l3 l6004d3 l6004f31 l6004v3 600 3 3 3 3 0.01 0.2 l2004l5 l2004d5 l2004f51 l2004v5 200 5 5 5 5 0.01 0.2 l4004l5 l4004d5 l4004f51 l4004v5 400 5 5 5 5 0.01 0.2 l6004l5 l6004d5 l6004f51 l6004v5 600 5 5 5 5 0.01 0.2 l2004l6 l2004d6 l2004f61 l2004v6 200 5 5 5 10 0.01 0.2 l4004l6 l4004d6 l4004f61 l4004v6 400 5 5 5 10 0.01 0.2 l6004l6 l6004d6 l6004f61 l6004v6 600 5 5 5 10 0.01 0.2 l2004l8 l2004d8 l2004f81 l2004v8 200 10 10 10 20 0.01 0.2 l4004l8 l4004d8 l4004f81 l4004v8 400 10 10 10 20 0.01 0.2 l6004l8 l6004d8 l6004f81 l6004v8 600 10 10 10 20 0.01 0.2 mt1 g mt2 g mt1 mt2 mt1 mt2 g mt2 mt2 mt1 g mt1 g mt2 mt2 mt2 mt2 g mt1 www..net
data sheets sensitive triacs ?2004 littelfuse lp e1 - 3 http://www.teccor.com thyristor product catalog +1 972-580-7777 see ?general notes? on page e1 - 4 and ?electrical specification notes? on page e1 - 5. v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (4) volts (2) (5) (15) volts (1) (7) mamps (13) amps (13) watts watts (8) (10) amps (1) (10) volts/sec (1) volts/ sec (9) sec amps 2 sec amps/sec t c = 25 c t c = 25 c60/50hz t c = 100 c max max max typ typ typ 1.6 2 5 1 10 0.2 10/8.3 0.5 20 2.8 0.41 20 1.6 2 5 1 10 0.2 10/8.3 0.5 15 2.8 0.41 20 1.6 2 5 1 10 0.2 10/8.3 0.5 10 2.8 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 20 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 15 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 10 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 30 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 25 3 0.41 20 1.6 2 10 1 10 0.2 10/8.3 1 20 3 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 35 3.2 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 30 3.2 0.41 20 1.6 2 15 1 10 0.2 10/8.3 2 25 3.2 0.41 20 1.625110 0.220/16.70.5 202.81.6 20 1.625110 0.220/16.70.5 202.81.6 20 1.625110 0.220/16.70.5 102.81.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 10 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 30 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 30 3 1.6 20 1.6 2 10 1 10 0.2 20/16.7 1 20 3 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 35 3.2 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 35 3.2 1.6 20 1.6 2 15 1 10 0.2 20/16.7 1 25 3.2 1.6 20 1.6 2 5 1.2 15 0.3 40/33 0.5 25 2.8 6.6 50 1.6 2 5 1.2 15 0.3 40/33 0.5 25 2.8 6.6 50 1.6 2 5 1.2 15 0.3 40/33 0.5 15 2.8 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 25 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 25 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 15 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 30 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 30 3 6.6 50 1.6 2 10 1.2 15 0.3 40/33 1 20 3 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 35 3.2 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 35 3.2 6.6 50 1.6 2 15 1.2 15 0.3 40/33 2 25 3.2 6.6 50 www..net
sensitive triacs data sheets http://www.teccor.com e1 - 4 ?2004 littelfuse lp +1 972-580-7777 thyristor product catalog specified test conditions di/dt ? maximum rate-of-change of on-state current; i gt = 50 ma with 0.1 s rise time dv/dt ? critical rate-of-rise of off-state voltage at rated v drm gate open dv/dt(c) ? critical rate-of-rise of commutation voltage at rated v drm and i t(rms) commutating di/dt = 0.54 rated i t(rms) /ms; gate unenergized i 2 t ? rms surge (non-repetitive) on-state current for period of 8.3 ms for fusing i drm ? peak off-state current, gate open; v drm = max rated value i gt ? dc gate trigger current in specific operating quadrants; v d = 12 v dc; r l = 60 ? i gtm ? peak gate trigger current i h ? holding current gate open; initial on-state current = 100 ma dc i t(rms) ? rms on-state current conduction angle of 360 i tsm ? peak one-cycle surge p g(av) ? average gate power dissipation p gm ? peak gate power dissipation; i gt i gtm t gt ? gate controlled turn-on time; i gt = 50 ma with 0.1 s rise time v drm ? repetitive peak off-state/blocking voltage v gt ? dc gate trigger voltage; v d = 12 v dc; r l = 60 ? v tm ? peak on-state voltage at max rated rms current general notes ? all measurements are made with 60 hz resistive load and at an ambient temperature of +25 c unless otherwise specified. ? operating temperature range (t j ) is -65 c to +110 c for to-92 devices and -40 c to +110 c for all other devices. ? storage temperature range (t s ) is -65 c to +150 c for to-92 devices, -40 c to +150 c for to-202 devices, and -40 c to +125 c for to-220 devices. ? lead solder temperature is a maximum of 230 c for 10 seconds maximum at a minimum of 1/16? (1.59 mm) from case. ? the case or lead temperature (t c or t l ) is measured as shown on dimensional outline drawings. s ee ?package dimensions? section of this catalog. i t(rms) part no. v drm i gt i drm isolated non-isolated (11) to-220 to-252 d-pak to-251 v-pak (1) volts (3) (6) mamps (1) (14) mamps qi qii qiii qiv t c = 25 c t c = 110 c max see ?package dimensions? section for variations. (12) min max max 6a l2006l5 l2006d5 l2006v5 200 5555 0.02 0.5 l4006l5 l4006d5 l4006v5 400 5555 0.02 0.5 l6006l5 l6006d5 l6006v5 600 5555 0.02 0.5 l2006l6 l2006d6 l2006v6 200 5 5 5 10 0.02 0.5 l4006l6 l4006d6 l4006v6 400 5 5 5 10 0.02 0.5 l6006l6 l6006d6 l6006v6 600 5 5 5 10 0.02 0.5 l2006l8 l2006d8 l2006v8 200 10 10 10 20 0.02 0.5 l4006l8 l4006d8 l4006v8 400 10 10 10 20 0.02 0.5 l6006l8 l6006d8 l6006v8 600 10 10 10 20 0.02 0.5 8a l2008l6 l2008d6 l2008v6 200 5 5 5 10 0.02 0.5 l4008l6 l4008d6 l4008v6 400 5 5 5 10 0.02 0.5 l6008l6 l6008d6 l6008v6 600 5 5 5 10 0.02 0.5 l2008l8 l2008d8 l2008v8 200 10 10 10 20 0.02 0.5 l4008l8 l4008d8 l4008v8 400 10 10 10 20 0.02 0.5 l6008l8 l6008d8 l6008v8 600 10 10 10 20 0.02 0.5 mt1 mt2 g mt2 mt2 mt1 g mt2 mt2 g mt1 www..net
data sheets sensitive triacs ?2004 littelfuse lp e1 - 5 http://www.teccor.com thyristor product catalog +1 972-580-7777 electrical specification notes (1) for either polarity of mt2 with reference to mt1 terminal (2) for either polarity of gate voltage v gt with reference to mt1 terminal (3) see gate characteristics and definition of quadrants. (4) see figure e1.4 for i t versus v t . (5) see figure e1.6 for v gt versus t c . (6) see figure e1.7 for i gt versus t c . (7) see figure e1.5 for i h versus t c . (8) see figure e1.9 for surge rating and specific duration. (9) see figure e1.8 for t gt versus i gt . (10) see figure e1.2 and figure e1.3 for maximum allowable case temperature at maximum rated current. (11) see figure e1.1, figure e1.2, and figure e1.3 for t a or t c versus i t(rms) . (12) see package outlines for lead form configurations. when ordering special lead forming, add type number as suffix to part number. (13) pulse width 10 s (14) t c or t l = t j for test conditions in off state (15) minimum non-trigger v gt at 110 c is 0.2 v. gate characteristics teccor triacs may be turned on between gate and mt1 terminals in the following ways: ? in-phase signals (with standard ac line) using quadrants i and iii ? application of unipolar pulses (gate always positive or nega- tive), using quadrants ii and iii with negative gate pulses and quadrants i and iv with positive gate pulses when maximum surge capability is required, pulses should be a minimum of one magnitude above i gt rating with a steep rising waveform ( 1 s rise time). definition of quadrants v tm v gt i h i gtm p gm p g(av) i tsm dv/dt(c) dv/dt t gt i 2 t di/dt (1) (4) volts (2) (5) (15) volts (1) (7) mamps (13) amps (13) watts watts (8) (10) amps (1) (10) volts/sec (1) volts/sec (9) sec amps 2 sec amps/sec t c = 25 c t c = 25 c 60/50 hz t c = 100 c max max max typ typ typ 1.6 2 10 1.6 18 0.4 60/50 1 40 3 15 70 1.6 2 10 1.6 18 0.4 60/50 1 30 3 15 70 1.6 2 10 1.6 18 0.4 60/50 1 20 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 40 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 30 3 15 70 1.6 2 10 1.6 18 0.4 60/50 2 20 3 15 70 1.6 2 20 1.6 18 0.4 60/50 2 45 3.2 15 70 1.6 2 20 1.6 18 0.4 60/50 2 40 3.2 15 70 1.6 2 20 1.6 18 0.4 60/50 2 30 3.2 15 70 1.6 2 10 1.6 18 0.4 80/65 2 40 3 26.5 70 1.6 2 10 1.6 18 0.4 80/65 2 30 3 26.5 70 1.6 2 10 1.6 18 0.4 80/65 2 20 3 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 45 3.2 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 40 3.2 26.5 70 1.6 2 20 1.6 18 0.4 80/65 2 30 3.2 26.5 70 mt2 positive (positive half cycle) mt2 negative (negative half cycle) mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + - www..net
sensitive triacs data sheets http://www.teccor.com e1 - 6 ?2004 littelfuse lp +1 972-580-7777 thyristor product catalog electrical isolation teccor?s isolated triac packages withstand a minimum high potential test of 2500 v ac rms from leads to mounting tab over the device's operating temperature range. the following isolation table shows standard isolation ratings. * ul recognized file #e71639 * mounted on 1 cm 2 copper foil surface; two-ounce copper foil figure e1.1 maximum allowable ambient temperature versus on-state current figure e1.2 maximum allowable case temperature versus on-state current (0.8 a and 1 a) electrical isolation from leads to mounting tab v ac rms to-220 * 2500 standard thermal resistance (steady state) junction to mounting tab and junction to ambient r jc [r ja ] c/w (typ) package code ecflf2dv type to-92 plastic compak to-202 type 1 to-220 isolated to-202 type 2 to-252 d-pak to-251 v-pak 0.8 a 60 [135] 60 * 1 a 50 [95] 40 * 4a 3.5 [45] 3.6 [50] 6.0 [70] 3.5 6.0 [70] 6a 3.3 3.2 3.2 8a 2.8 2.7 2.7 20 40 60 80 100 120 rms on-state current [i t(rms) ] - amps maximum allowable ambient temperature ( t a ) - ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? free air rating ?no heatsink to-220 and type 1 and 3 to-202 type 2 and 4 to-202 and to-251 0.8 a to-92 1 a to-92 25 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 50 60 70 80 90 100 110 maximum allowable case temperature (t c ) ??c current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawings rms on-state current [i t(rms) ] ?amps 1 a 0.8 a www..net
data sheets sensitive triacs ?2004 littelfuse lp e1 - 7 http://www.teccor.com thyristor product catalog +1 972-580-7777 figure e1.3 maximum allowable case temperature versus on-state current (4 a, 6 a, and 8 a) figure e1.4 on-state current versus on-state voltage (typical) figure e1.5 normalized dc holding current versus case temperature figure e1.6 normalized dc gate trigger voltage for all quadrants versus case temperature figure e1.7 normalized dc gate trigger current for all quadrants versus case temperature figure e1.8 turn-on time versus gate trigger current (typical) 01 23 4 5 6 7 8 60 65 70 75 80 85 90 95 100 105 110 rms on-state current [i t(rms) ] - amps maximum allowable case temperature ( t c ) - ?c current waveform: sinusoidal load: resistive or inductive conduction angle: 360? case temperature: measured as shown on dimensional drawings 4 a type 1 and 3 to-202 4 a to-220 (isolated) 4 a to-252 8 a to-220 (isolated) 6 a to-220 (isolated) 4 a type 2 and 4 to-202 4 a to-251 8 a to-251 and to-252 6 a to-251 6 a to-252 0 0.5 0.8 1.0 1.2 1.4 1.6 1.8 0 2 4 6 8 10 12 14 16 18 20 positive or negative instantaneous on-state voltage (v t ) - volts positive or negative instantaneous on-state current (i t ) - amps 1 a 4 a 6 a and 8 a t c = 25 ? c 0.8 a -40 -15 +25 +65 +110 +125 0 1.0 2.0 3.0 4.0 -65 case temperature ( t c ) - ? c initial on-state current = 100 ma (dc) 0.8 - 4 a devices = 200 ma (dc) 6 - 8 a devices ratio of i h i h (t c = 25 ? c) -65 -40 -15 +65 +110 +125 +25 0 .5 1.0 1.5 2.0 ratio of v gt v gt (t c = 25 ?c) case temperature ( t c ) - ? c -65 -40 -15 +65 +110 +125 +25 0 1.0 2.0 3.0 4.0 ratio of i gt i gt (t c = 25 ?c) case temperature (t c ) - ?c 12346 5 8 10 20 30 40 60 80 100 i gt = 5 ma max i gt = 10 ma max i gt = 20 ma max i gt = 3 ma max 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 dc gate trigger current (i gt ) - ma turn-on time (t gt ) - sec t c = 25 ?c www..net
sensitive triacs data sheets http://www.teccor.com e1 - 8 ?2004 littelfuse lp +1 972-580-7777 thyristor product catalog figure e1.9 peak surge current versus surge current duration figure e1.10 power dissipation (typical) versus rms on-state current (0.8 a and 1 a) figure e1.11 power dissipation (typical) versus rms on-state current (4 a, 6 a, and 8 a) 1 24 368102040 30 60 100 200 400 600 1000 1 2 3 4 6 10 8 20 30 40 60 100 80 150 200 surge current duration ?full cycles peak surge (non-repetitive) on-state current (i tsm ) ?amps 8 a 6 a 0.8 a supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at specified case temperature notes: 1) gate control may be lost during and immediately following surge current interval. 2) overload may not be repeated until junction temperature has returned to steady-state rated value. 1 a 4 a 0 0.25 0.50 0.75 1.0 1.25 1.5 0 0.5 1.0 1.5 rms on-state current [i t(rms) ] ?amps average on-state power dissipation [p d(av) ] ?watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360? 1 a 0.8 a 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 8.0 6 a and 8 a 4 a rms on-state current [i t(rms) ] ?amps average on-state power dissipation [p d(av) ] ?watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360 ? www..net
|
